Altera Triple Speed Ethernet MegaCore Function Manual do Utilizador Página 124
- Página / 223
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
DescriptionI/OName
Assert this active-low signal to put the node into a power-down state.
If magic packets are supported (the MAGIC_ENA bit in the command_
config register is set to 1), the receiver logic stops writing data to the
receive FIFO buffer and the magic packet detection logic is enabled.
Setting this signal to 1 restores the normal frame reception mode.
This signal is present only if the Enable magic packet detection option
is turned on.
Imagic_sleep_n
If the MAC function is in the power-down state, the MAC function
asserts this signal to indicate that a magic packet has been detected
and the node is requested to restore its normal frame reception mode.
This signal is present only if the Enable magic packet detection option
is turned on.
0magic_wakeup
MII/GMII/RGMII Signals
Table 7-10: GMII/RGMII/MII Signals
DescriptionI/OName
GMII Transmit
GMII transmit data bus.Igm_tx_d[7:0]
Asserted to indicate that the data on the GMII transmit data bus is
valid.
Ogm_tx_en
Asserted to indicate to the PHY that the frame sent is invalid.Ogm_tx_err
GMII Receive
GMII receive data bus.Igm_rx_d[7:0]
Assert this signal to indicate that the data on the GMII receive data bus
is valid. Keep this signal asserted during frame reception, from the first
preamble byte until the last byte of the CRC field is received.
Igm_rx_dv
The PHY asserts this signal to indicate that the receive frame contains
errors.
Igm_rx_err
RGMII Transmit
RGMII transmit data bus. Drives gm_tx_d[3:0] on the positive edge
of tx_clk and gm_tx_d[7:4] on the negative edge of tx_clk.
Orgmii_out[3:0]
Control output signal. Drives gm_tx_en on the positive edge of tx_clk
and a logical derivative of (gm_tx_en XOR gm_tx_err) on the negative
edge of tx_clk.
Otx_control
RGMII Receive
RGMII receive data bus. Expects gm_rx_d[3:0] on the positive edge
of rx_clk and gm_rx_d[7:4] on the negative edge of rx_clk.
Irgmii_in[3:0]
Altera Corporation
Interface Signals
Send Feedback
7-9
MII/GMII/RGMII Signals
UG-01008
2014.06.30
- User Guide 1
- Contents 2
- Altera Corporation 10
- About This MegaCore Function 10
- Send Feedback 10
- High-Level Block Diagrams 10
- Figure 1-2: Multi-port MAC 11
- 10/100/1000-Mbps 12
- Ethernet MAC 12
- Optical Platform 14
- Copper Platform 14
- Release Information 18
- DescriptionItem 19
- Using the Parameter Editor 24
- Design Walkthrough 25
- Simulate the System 27
- Programming an FPGA Device 27
- Generated Files 28
- DescriptionFile Name 29
- Quartus II Pin 29
- Assignment 29
- Parameter Settings 30
- Ethernet MAC Options 31
- FIFO Options 33
- Timestamp Options 34
- PCS/Transceiver Options 34
- ParameterValueName 35
- Functional Description 37
- MAC Architecture 38
- MAC Interfaces 39
- MAC Transmit Datapath 40
- IP Payload Re-alignment 41
- Address Insertion 41
- Frame Payload Padding 41
- CRC-32 Generation 41
- Interpacket Gap Insertion 42
- MAC Receive Datapath 43
- ValueHash Code Bit 44
- Frame Type Validation 45
- Payload Pad Removal 46
- CRC Checking 46
- Length Checking 46
- Frame Writing 47
- IP Payload Alignment 47
- FIFO Buffer Thresholds 48
- Receive Thresholds 49
- Transmit Thresholds 51
- Congestion and Flow Control 52
- Magic Packets 53
- MAC Local Loopback 54
- MAC Error Correction Code 55
- MAC Reset 55
- PHY Management (MDIO) 56
- MDIO Connection 57
- MDIO Frame Format 57
- Gigabit Ethernet 58
- Programmable 10/100 Ethernet 59
- Transmit Operation 62
- Receive Operation 63
- SGMII Converter 64
- Auto-Negotiation 65
- SGMII Auto-Negotiation 66
- Ten-bit Interface 68
- PHY Loopback 69
- PHY Power-Down 69
- POWERDOWN 70
- 1000BASE-X PCS 70
- IEEE 1588v2 Features 72
- Time of Day 73
- IEEE 1588v2 Receive Datapath 74
- IEEE 1588v2 Frame Format 74
- 0..1500/9600 Octets 75
- 4 Octets 75
- CRC4 Octets 76
- 0..1500/9600 Octets Payload 76
- MAC Header 77
- UDP Header 77
- IP Header 77
- PTP Header 77
- Software Requirements 78
- Base Addresses 80
- IEEE 1588v2 Feature PMA Delay 100
- UG-01008 101
- 2014.06.30 101
- DescriptionR/WNameBit(s) 103
- DescriptionR/WNameBit 105
- 1000BASE-X 106
- Register Initialization 110
- Configuration Register Space 111
- Interface Signals 116
- Clock and Reset Signal 117
- MAC Control Interface Signals 118
- MAC Status Signals 118
- MAC Receive Interface Signals 119
- DescriptionBit 120
- DescriptionI/OName 123
- MII/GMII/RGMII Signals 124
- PHY Management Signals 125
- ECC Status Signals 126
- TBI Interface Signals 131
- Status LED Control Signals 132
- SERDES Control Signals 132
- Related Information 133
- SectionInterface Signal 135
- 1.25 Gbps Serial Interface 138
- Transceiver Native PHY Signal 138
- DescriptionWidthI/OSignal 141
- 1000BASE-X/SGMII PCS Signals 149
- PCS Control Interface Signals 150
- PCS Reset Signals 150
- SGMII Status Signals 152
- Avalon-ST Receive Interface 155
- IEEE 1588v2 Timestamp 162
- Design Considerations 163
- Configurations(1) 164
- Sharing Transceiver Quads 169
- Timing Constraints 171
- Recommended Clock Frequency 173
- 50–100CLK 174
- 1000BASE-X/SGMII PCS only 174
- 125REF_CLK 174
- 125TBI_TX_CLK 174
- 125TBI_RX_CLK 174
- Testbench 175
- Testbench Verification 176
- Testbench Configuration 177
- Test Flow 177
- Simulation Model 178
- Simulation Model Files 179
- Driver Architecture 180
- PHY Speed Bits 181
- Speed (Mbps) 181
- Using Jumbo Frames 183
- API Functions 184
- Constants 189
- DescriptionValueConstant 190
- Ethernet Frame Format 192
- Pause Frame Format 194
- Description 195
- XON_GENXOFF_GEN 195
- Simulation Parameters 196
- DefaultDescriptionParameter 197
- Test Configuration Parameters 198
- Time-of-Day (ToD) Clock 201
- ToD Clock Parameter Setting 202
- ToD Clock 203
- DescriptionR/WNameDword 205
- Adjusting ToD Clock Drift 206
- ToD Synchronizer 207
- ToD Synchronizer Block 208
- 32/6364/31516/6364/63Settings 209
- DescriptionValueName 209
- ToD Synchronizer Signals 210
- Packet Classifier 212
- Packet Classifier Signals 213
- Additional Information 217
- Document Revision History 218
- ChangesVersionDate 219
- How to Contact Altera 223
Manuais e produtos relacionados com Instrumentos de medida Altera Triple Speed Ethernet MegaCore Function
Instrumentos de medida Altera 8B10B Encoder/Decoder MegaCore Function Manual do Utilizador
(32 páginas)
(32 páginas)
Instrumentos de medida Altera I/O Phase-Locked Loop (Altera IOPLL) IP Core Manual do Utilizador
(11 páginas)
(11 páginas)
Instrumentos de medida Altera Embedded Systems Development Kit, Cyclone III Edit Manual do Utilizador
(82 páginas)
(82 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.056 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais