Altera DDR SDRAM High-Performance Controllers and ALTMEMP Manual do Utilizador Página 117
- Página / 140
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Chapter 6: Functional Description—High-Performance Controller II 6–23
Register Maps
June 2011 Altera Corporation External Memory Interface Handbook Volume 3
Section I. DDR and DDR2 SDRAM Controllers with ALTMEMPHY IP User Guide
Table 6–14. ALTMEMPHY Register Map (Part 1 of 2)
Address Bit Name Default Access Description
0x005
2:0 Burst length 8 Read only This value is set to 8.
3 BT 0 Read only This value is set to 0.
6:4 CAS latency — Read write
CAS latency setting. The default value for
these bits is set by the MegaWizard CAS
Latency setting for your controller instance.
You must set this value in the CSR interface
register map 0x126 as well.
7 Reserved 0 — Reserved for future use.
8 DLL 0 Read write
Not used by the controller, but you can set
and program into the memory device mode
register.
11:9 Write recovery — Read write
Write recovery (t
WR
) setting. The default
value for these bits is set by the
MegaWizard Write Recovery setting for
your controller instance. You must set thi
svalue in CSR interface register map 0x126
as well.
12 PD 0/1 Read only This value is set to 0.
15:13 Reserved 0 C Reserved for future use.
16 DLL 0 Read write
Not used by the controller, but you can set
and program into the memory device mode
register.
17 ODS 0 Read write
18 RTT 0 Read write
21:19 AL — Read write
Additive latency setting. The default value
for these bits is set by the MegaWizard
Additive Latency setting for your controller
instance. You must set this value in CSR
interface register map 0x126 as well.
22 RTT 0 Read write
Not used by the controller, but you can set
and program into the memory device mode
register.
25:23 RTT/WL/OCD 0 Read write
26 DQS# 0 Read write
27 TDQS/RDQS 0 Read write
28 QOFF 0 Read write
31:29 Reserved 0 — Reserved for future use.
- ALTMEMPHY IP User Guide 1
- Contents 3
- Chapter 7. Latency 5
- Chapter 8. Timing Diagrams 5
- 1. About This IP 7
- Release Information 8
- Device Family Support 8
- Features 9
- Unsupported Features 10
- MegaCore Verification 10
- Resource Utilization 11
- System Requirements 12
- Installation and Licensing 13
- 1–8 Chapter 1: About This IP 14
- 2. Getting Started 15
- SOPC Builder Flow 16
- Qsys Flow 18
- Completing the Qsys System 19
- Specifying Parameters 20
- HardCopy Guidelines 21
- Generated Files 22
- 3. Parameter Settings 27
- Memory Settings 28
- ALTMEMPHY Parameter Settings 29
- Note to Table 3–3: 32
- Note to Table 3–5: 34
- PHY Settings 36
- Board Settings 38
- ■ Memory Settings 39
- ■ PHY Settings 39
- ■ Board Settings 39
- ■ Controller Settings 39
- Controller Settings 40
- 4. Compiling and Simulating 43
- Compiling the Design 44
- Simulating the Design 46
- Block Description 48
- Calibration 49
- Address and Command Datapath 49
- ), or the inverted 50
- Clock and Reset Management 51
- Notes to Table 5–4: 54
- Note to Table 5–2: 57
- Cyclone III Devices 59
- Read Datapath 66
- Note to Figure 5–6: 68
- Note to Figure 5–8: 70
- Devices 71
- GX Devices 72
- ALTMEMPHY Signals 73
- Notes to Table 5–5: 74
- Note to Table 5–5: 77
- Notes to Table 5–7: 79
- PHY-to-Controller Interfaces 80
- Altera Device 81
- -- a --b 82
- Figure 5–15. Full-Rate Reads 83
- Figure 5–16. Half-Rate Reads 83
- Notes to Figure 5–17: 85
- Notes to Figure 5–18: 86
- Notes to Figure 5–19: 87
- Notes to Figure 5–20: 88
- Preliminary Steps 89
- Design Considerations 89
- Clocks and Resets 89
- Using a Custom Controller 90
- Partial Write Operations 92
- 6. Functional Description— 95
- Avalon-ST Input Interface 96
- Command Generator 96
- Timing Bank Pool 96
- Arbitration Rules 97
- CSR Interface 98
- Data Reordering 98
- Pre-emptive Bank Management 98
- Quasi-1T and Quasi-2T 98
- User Autoprecharge Commands 98
- User-Controlled Self-Refresh 99
- DDR2 SDRAM 100
- Partial Writes 101
- Partial Bursts 102
- External Interfaces 103
- Memory Side-Band Signals 104
- Top-Level Signals Description 105
- ■ Full rate controllers 107
- ■ Half rate controllers 107
- Sequence of Operations 111
- Read Command 112
- Read-Modify-Write Command 112
- Example Top-Level File 113
- Example Driver 114
- Register Maps 116
- Controller Register Map 118
- 7. Latency 123
- 7–2 Chapter 7: Latency 124
- Note to Table 7–2: 125
- SDRAM values 126
- Handbook 127
- 7–6 Chapter 7: Latency 128
- 8. Timing Diagrams 129
- Half-Rate Read 130
- Half-Rate Write 132
- Full-Rate Read 134
- Full-Rate Write 136
- Additional Information 139
- Typographic Conventions 140
Manuais e produtos relacionados com Instrumentos de medida Altera DDR SDRAM High-Performance Controllers and ALTMEMP
Instrumentos de medida Altera Nios II Embedded Evaluation Kit Cyclone III Editio Manual do Utilizador
(3 páginas)
(3 páginas)
Instrumentos de medida Altera Nios II Embedded Evaluation Kit Cyclone III Editio Manual do Utilizador
(80 páginas)
(80 páginas)
Instrumentos de medida Altera Phase-Locked Loop Reconfiguration IP Core Manual do Utilizador
(51 páginas)
(51 páginas)
Instrumentos de medida Altera Serial Digital Interface (SDI) MegaCore Function Manual do Utilizador
(140 páginas)
(140 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.760 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais