Altera Arria 10 Avalon-ST Manual do Utilizador Página 257
- Página / 275
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Related Information
BFM Log and Message Procedures on page 17-42
Setting Up Simulation
Changing the simulation parameters reduces simulation time and provides greater visibility.
Changing Between Serial and PIPE Simulation
By default, the Altera testbench runs a serial simulation. You can change between serial and PIPE
simulation by editing the top-level testbench file.
The serial_sim_hwtcl and enable_pipe32_phyip_ser_driver_hwtcl parameters control whether
simulation is in serial mode or PIPE simulation mode. The parameters are defined in the top-level
testbench, <working_dir>/ep_g1x8_tb/ep_g1x8_tb/sim/ep_g1x8_tb.v.
Table 17-22: Controlling Serial and PIPE Simulations
Data Rates
Parameter Settings
serial_sim_hwtcl enable_pipe32_phyip_ser_driver_hwtcl
Serial simulation 1 0
PIPE simulation 0 1
Using the PIPE Interface for Gen1 and Gen2 Variants
Running the simulation in PIPE mode reduces simulation time and provides greater visibility.
Complete the following steps to simulate using the PIPE interface:
1. Change to your simulation directory, <work_dir>/<variant>/testbench/<variant>_tb/simulation
2. Open <variant>_tb.v.
3. Search for the string, serial_sim_hwtcl. Set the value of this parameter to 0 if it is 1.
4. Save <variant>_tb.v.
Viewing the Important PIPE Interface Signals
You can view the most important PIPE interface signals, txdata, txdatak, rxdata, and rxdatak at the
following level of the design hierarchy: altpcie_<device>_hip_pipen1b|
twentynm_hssi_<gen>_<lanes>_pcie_hip.
Disabling the Scrambler for Gen1 and Gen2 Simulations
The encoding scheme implemented by the scrambler applies a binary polynomial to the data stream to
ensure enough data transitions between 0 and 1 to prevent clock drift. The data is decoded at the other
end of the link by running the inverse polynomial.
UG-01145_avst
2015.05.04
Setting Up Simulation
17-57
Testbench and Design Example
Altera Corporation
Send Feedback
- Solutions 1
- Contents 2
- Datasheet 8
- Arria 10 Features 9
- Interface 10
- UG-01145_avst 11
- 2015.05.04 11
- Release Information 13
- Device Family Support 14
- Configurations 14
- Altera FPGA 15
- Debug Features 17
- IP Core Verification 18
- Recommended Speed Grades 18
- Qsys Design Flow 21
- Generating the Testbench 22
- Simulating the Example Design 22
- Directory Description 23
- Time TLP Type Payload 23
- TLP Header 23
- Modifying the Example Design 26
- Component 27
- File Name Description 28
- Subscribe 31
- 2014.08.18 32
- Generating the Qsys System 33
- Parameter Value 34
- Parameter Settings 44
- Parameter Value Description 45
- Device Capabilities 52
- Error Reporting 53
- Link Capabilities 54
- MSI and MSI-X Capabilities 55
- Slot Capabilities 56
- Power Management 57
- PHY Characteristics 58
- Avalon‑ST RX Interface 68
- Packet TLP 73
- Aligned Addresses 77
- Avalon-ST TX Interface 82
- Single Packet Per Cycle 95
- Data 0 Header 2 96
- Clock Signals 97
- Signal Direction Description 100
- Related Information 101
- ECRC Forwarding 102
- Error Signals 102
- Interrupts for Endpoints 103
- Interrupts for Root Ports 104
- Completion Side Band Signals 104
- Signal Directi 105
- Description 105
- Parity Signals 107
- LMI Signals 108
- Altera Corporation 112
- Send Feedback 112
- D E F 0 1 2 3 113
- Field and Bit Map 117
- 0134678951 117
- Bit(s) Field Description 118
- Power Management Signals 120
- 15 011623 8 2791213142431 121
- Bits Field Description 122
- Serial Data Signals 123
- PIPE Interface Signals 123
- Test Signals 128
- Registers 129
- Altera-Defined VSEC Registers 136
- CvP Registers 137
- Bits Register Description 141
- Arria 10 Reset and Clocks 144
- Clock Domains 147
- Clock Summary 149
- Interrupts 150
- MSI Interrupts 151
- Allocated 152
- Implementing MSI-X Interrupts 153
- Legacy Interrupts 155
- Error Handling 157
- Physical Layer Errors 158
- Data Link Layer Errors 158
- Transaction Layer Errors 159
- Error Type Description 160
- Status Bit Conditions 163
- IP Core Architecture 165
- Hard IP for PCI Express 166
- Top-Level Interfaces 167
- Clocks and Reset 168
- Hard IP Reconfiguration 168
- Transaction Layer 169
- Configuration Space 170
- (Soft Logic) 172
- Data Link Layer 174
- Physical Layer 176
- TX Packets 177
- Supported Message Types 179
- Power Management Messages 180
- Error Signaling Messages 181
- Locked Transaction Message 182
- Slot Power Limit Message 182
- Vendor-Defined Messages 182
- Hot Plug Messages 183
- Receive Buffer Reordering 185
- Using Relaxed Ordering 187
- Throughput Optimization 190
- Throughput of Posted Writes 192
- Design Implementation 194
- SDC Timing Constraints 195
- Optional Features 196
- ECRC on the RX Path 197
- ECRC on the TX Path 198
- TLP on Applica‐ 199
- TLP on Link Comments 199
- Testbench and Design Example 201
- Root Port Testbench 203
- Chaining DMA Design Examples 204
- Root Complex 205
- Chaining DMA 205
- Hard IP for 205
- PCI Express 205
- BAR/Address Map 208
- Memory BAR Mapping 209
- Bit Field Description 210
- Addr Register Name 211
- Byte Address 213
- Offset to Base 213
- Descriptor Type Description 213
- Test Driver Module 215
- DMA Write Cycles 216
- DMA Read Cycles 218
- Root Port Design Example 220
- Root Port 221
- Variation 221
- (variation_name.v) 221
- Root Port BFM 222
- BFM Configuration Procedures 223
- BFM Request Interface 223
- BFM Memory Map 224
- Offset (Bytes) Description 226
- BFM Procedures and Functions 230
- Location altpcietb_bfm_rdwr.v 231
- Shared Memory Constants 239
- Constant Description 240
- Location 245
- Setting Up Simulation 257
- Debugging 259
- Use Third-Party PCIe Analyzer 263
- BIOS Enumeration Issues 263
- Frequently Asked Questions 264
- 7 6 5 4 3 2 1 0 265
- Core Config 8 4 1 265
- Additional Information 267
- Date Version Changes Made 268
- How to Contact Altera 272
- Typographic Conventions 273
- Visual Cue Meaning 274
Manuais e produtos relacionados com Instrumentos de medida Altera Arria 10 Avalon-ST
Instrumentos de medida Altera DDR SDRAM High-Performance Controllers and ALTMEMP Manual do Utilizador
(140 páginas)
(140 páginas)
Instrumentos de medida Altera Nios II Embedded Evaluation Kit Cyclone III Editio Manual do Utilizador
(3 páginas)
(3 páginas)
Instrumentos de medida Altera Nios II Embedded Evaluation Kit Cyclone III Editio Manual do Utilizador
(80 páginas)
(80 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.074 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais