Altera Serial Digital Interface (SDI) MegaCore Function Manual do Utilizador Página 58
- Página / 140
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
3–28 Chapter 3: Functional Description
Block Description
Serial Digital Interface (SDI) MegaCore Function February 2013 Altera Corporation
User Guide
Table 3–10 lists the transceiver dynamic reconfiguration requirements.
Table 3–11 lists the rates for the different SDI standards.
To reprogram the transceivers, you must include the ALT2GXB_RECONFIG or
ALTGX_RECONFIG megafunction in your design. However, to reprogram
Arria II GX or Stratix IV device family, you require an ALTGX_RECONFIG
megafunction. You can get this parameterization from the
example\a2gx_tr\source\sdi_dprio_siv directory in the example design. Similarly,
to reprogram Cyclone IV GX device family with channel reconfiguration mode, you
require a slightly different configuration of the ALTGX_RECONFIG megafunction.
You can get this parameterization from the
simulation\modelsim\trsdi_c4gx\channel_reconfig\testbench\pattern_gen
directory in the example simulation.
f For more information about the ALT2GXB_RECONFIG megafunction, refer to the
Stratix II GX ALT2GXB_RECONFIG Megafunction User Guide. For more information
about the ALTGX_RECONFIG megafunction, refer to the Stratix IV
ALTGX_RECONFIG Megafunction User Guide.
Table 3–10. Transceiver Dynamic Reconfiguration Requirements
SDI Standard Receiver Transmitter
(1)
Duplex
(1)
SD-SDI No Yes Yes
HD-SDI No Yes Yes
3G-SDI No Yes Yes
Dual link No Yes Yes
Dual standard Yes Yes Yes
Triple standard Yes Yes Yes
Note to Table 3–10:
(1) If the additional serial reference clock feature is enabled, the transmitters require dynamic reconfiguration to
enable toggling switching between the two input clocks.
Table 3–11. SDI Standard Rates
SDI Standard Data Rate Oversampling
Transceiver
Rate (MHz)
Transceiver
Reference Clock
(MHz)
rx_clk Rate
SD-SDI 270 Mbps 11 times 2,970 148.5 148.5
HD-SDI 1.485 Gbps None 1,485 148.5
(1)
74.25
(1)
3G-SDI 2.970 Gbps None 2,970 148.5
(1)
148.5
(1)
Note to Table 3–11:
(1) Also supports the 1/1.001 rates for all supported devices, except Cyclone IV GX devices. For Cyclone IV GX
devices, the transceiver reference clock must be 148.35 MHz to support the 1/1.001 rates.
- User Guide 1
- Contents 3
- Chapter 4. SDI Audio IP Cores 4
- Appendix A. Constraints 5
- Appendix B. Clocking 5
- Features 7
- Release Information 8
- Device Family Support 8
- General Description 9
- Notes to Table 1–5: 10
- OpenCore Plus Evaluation 11
- Resource Utilization 12
- 2. Getting Started 15
- Design Flow 16
- SDI Walkthrough 17
- Parameterizing 19
- Setting Up Simulation 20
- Generating Files 20
- - SD 270 Mbps 22
- - HD 1.485 Gbps 22
- - 3G 2.97 Gbps 22
- Simulating the Design 23
- Specifying Constraints 25
- Multiple Channels 26
- Compiling the Design 28
- Programming a Device 28
- Setting Up Licensing 29
- 3. Functional Description 31
- Block Description 32
- HD-SDI LN Insertion 34
- Scrambling and NRZI Coding 35
- Transceiver Clock 35
- Receiver 36
- Word Alignment 38
- Video Timing Flags Extraction 39
- RP168 Switching Compliance 39
- HD-SDI LN Extraction 40
- HD-SDI CRC Checking 40
- Accessing Transceiver 40
- Transmitter 42
- Transmitter Clocks 42
- Receiver Clocks 43
- Notes to Table 3–5: 44
- Notes to Figure 3–8: 44
- Figure 3–9. Receiver Clocks 46
- rxdata 47
- Note to Table 3–7: 50
- Notes to Figure 3–11: 51
- Figure 3–12. Receiver Clocks 53
- New TRS reasserts 55
- Stratix IV GX 57
- Note to Table 3–10: 58
- Note to Table 3–11: 58
- Notes to Figure 3–18: 60
- Note to Figure 3–19: 61
- User Logic 62
- Encrypted SDI IP Core 62
- Cyclone IV GX 63
- Notes to Table 3–12: 70
- Note to Table 3–13: 70
- Note to Table 3–14: 71
- Note to Figure 3–30: 77
- Notes to Figure 3–33: 78
- signal in 82
- Table 3–18 on page 3–50 82
- Notes to Figure 3–40: 83
- Notes to Table 3–19: 85
- MegaCore Verification 87
- 4. SDI Audio IP Cores 89
- Functional Description 90
- Note to Table 4–4: 93
- Note to Table 4–5: 94
- MegaCore function 100
- Register Maps 103
- Parameters 105
- AES Format 109
- Avalon-ST Audio Interface 109
- Note to Figure 4–6: 110
- Instantiating the IP Cores 111
- Simulating the Testbench 112
- Design Example 113
- Components 114
- Hardware Setup 116
- D6 D7 D8 D9 D10 D11 D12 D13 118
- A. Constraints 123
- Notes to Figure A–1: 124
- (gxb_rxclk 125
- Specify Clock Characteristics 126
- Set Multicycle Paths 127
- 337.5-MHz Zero-degree Clocks 128
- Minimize Timing Skew 129
- Non Cyclone Devices 130
- Cyclone Devices Only 131
- A–10 Appendix A: Constraints 132
- B. Clocking 133
- B–2 Appendix B: Clocking 134
- C. Receive and Retransmit 135
- Loopback FIFO Buffer 136
- Additional Information 137
- Info–2 Additional Information 138
- Document Revision History 138
- How to Contact Altera 139
- Typographic Conventions 139
- Info–4 Additional Information 140
Manuais e produtos relacionados com Instrumentos de medida Altera Serial Digital Interface (SDI) MegaCore Function
Instrumentos de medida Altera 100G Development Kit, Stratix V GX Edition Manual do Utilizador
(44 páginas)
(44 páginas)
Instrumentos de medida Altera Stratix V Avalon-MM Interface for PCIe Solutions Manual do Utilizador
(184 páginas)
(184 páginas)
Instrumentos de medida Altera 10-Gbps Ethernet MAC MegaCore Function Manual do Utilizador
(175 páginas)
(175 páginas)
Instrumentos de medida Altera Triple Speed Ethernet MegaCore Function Manual do Utilizador
(223 páginas)
(223 páginas)
Instrumentos de medida Altera 8B10B Encoder/Decoder MegaCore Function Manual do Utilizador
(32 páginas)
(32 páginas)
Instrumentos de medida Altera I/O Phase-Locked Loop (Altera IOPLL) IP Core Manual do Utilizador
(11 páginas)
(11 páginas)
Instrumentos de medida Altera Embedded Systems Development Kit, Cyclone III Edit Manual do Utilizador
(82 páginas)
(82 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.025 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais