Altera MAX 10 FPGA Manual do Utilizador Página 44
- Página / 56
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
• JEDEC STAPL Format (.jam)
• Jam STAPL Byte Code (.jbc)
• Serial Vector Format (.svf)
10.Type the file name in the File name field, or browse to and select the file.
11.Click OK to generate the .jam, .jbc or .svf file.
Programming .ekp File and Encrypted POF File
There are two methods to program the encrypted .pof and .ekp file:
• Program the .ekp and .pof separately.
• Integrate the .ekp into .pof and program both altogether.
Programming .ekp File and Encrypted .pof Separately
To program the .ekp and encrypted .pof separately using the Quartus II software, follow these steps:
1. In the Quartus II Programmer, under the Mode list, select JTAG as the programming mode.
2. Click Hardware Setup and the Hardware Setup dialog box will appear.
3. Select USBBlaster as the programming hardware in the Currently selected hardware list and click
Done.
4. Click Add File and the Select Programmer File dialog box will appear.
5.
Type <filename>.ekp in the File name field and click Open.
6. Select the .ekp file you added and click Program/Configure.
7. Click Start to program the key.
Note:
The Quartus II software message window provides information about the success or failure of
the key programming operation. Once the .ekp is programmed, .pof can be programmed
separately. To retain the security key in the internal flash that had been programmed through
the .ekp, continue with the following steps.
8. Select the .ekp to be programmed to the selected device.
9. Check only the functional block that need to be updated at child level. Do not check operation at the
parent level when using Programmer GUI.
10.After all settings are set, click Start to start programming.
Integrate the .ekp into .pof Programming
To integrate the .ekp into .pof and program both altogether using the Quartus II software, follow these
steps:
1. In the Quartus II Programmer, under the Mode list, select JTAG as the programming mode.
2. Click Hardware Setup and the Hardware Setup dialog box will appear.
3. Select USBBlaster as the programming hardware in the Currently selected hardware list and click
Done.
4. Click the Auto Detect button on the left pane.
5. Select the .pof you wish to program to the device.
6.
Select the <yourpoffile.pof>, right click and select Add EKP File to integrate .ekp file with the .pof
file.
3-14
Programming .ekp File and Encrypted POF File
UG-M10CONFIG
2015.05.04
Altera Corporation
MAX 10 FPGA Configuration Design Guidelines
Send Feedback
- 101 Innovation Drive 1
- San Jose, CA 95134 1
- Contents 2
- Altera Corporation 3
- Configuration Scheme 4
- Remote System 4
- Features 5
- Internal Configuration 6
- Configuration Flash Memory 7
- In-System Programming 8
- UG-M10CONFIG 10
- 2015.05.04 10
- Configuration Features 12
- Remote System Upgrade Flow 13
- Bits Name Description 17
- Values State Description 17
- User Watchdog Timer 18
- Configuration Design Security 19
- Unique Chip ID 20
- JTAG Secure Mode 20
- Verify Protect 21
- JTAG Instruction Availability 21
- Configuration Error Detection 23
- User Mode Error Detection 23
- Error Detection Timing 24
- Recovering from CRC Errors 26
- Configuration Details 27
- Power Up 28
- MAX 10 Configuration Pins 29
- JTAG Pin Sharing Behavior 30
- Pins Guidelines 31
- Enabling Dual-purpose Pin 32
- JTAG Configuration Setup 33
- Related Information 34
- .pof and ICB Settings 35
- Auto-Generated .pof 36
- Error Detection 38
- Enabling Error Detection 39
- Enabling Data Compression 40
- AES Encryption 41
- Send Feedback 46
- Key Y Key Y Enabled image 0 47
- Implementation Guides 48
- Offset R/W Width 50
- Description 50
- Parameter Value Description 52
- Configuration User Guide 54
- Date Version Changes 55
Manuais e produtos relacionados com Instrumentos de medida Altera MAX 10 FPGA
Instrumentos de medida Altera DDR3 SDRAM High-Performance Controller and ALTMEMP Manual do Utilizador
(10 páginas)
(10 páginas)
Instrumentos de medida Altera DDR SDRAM High-Performance Controllers and ALTMEMP Manual do Utilizador
(140 páginas)
(140 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.033 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais